How to fix error 0xc18a0401, oxc18a0401 on HP printers

Solution 1:

Press and hold the "*" key. Press the "#" key and release both keys. Display should say "Enter Special Key Combo"

Press and release in sequence the "1", "2" and "3" buttons. Display should say "Support" and display the FW rev (something like R0631R).

Press and release the right arrow button until the display says "System Configuration Menu".

Press and release the "OK" button. Display should say "Hardware failure status". If not there already, Arrow Key over to "Hardware failure status",

Press and release the "OK" button. Display should say "Hardware failure status: Clear. Press OK to clear".

Press and release the "OK" Button. Message changes to "Hardware failure status Cleared. Press Cancel to continue".

Press and release the "CANCEL" button as many times as necessary, until the "Welcome to Photosmart Express" screen appears, or, the "Ink System Failure" screen appears. Do not try to print at this stage.

Using the Power Button, turn the unit OFF and unplug the power cable from back of the printer and wall outlet.

Wait 30 seconds for the power to get discharged and then plug the power cable into the wall outlet first and then into the back of the printer.

Turn the unit on. The printer may display message "Use Power button to shutdown the printer" followed by "Press OK to continue". 

Press OK. The Printer will start the "One time ink initialization process". Allow this process to complete and do not interrupt. 

Once the initialization process is complete, the printer will print out a Diagnostic Page. 

Solution 2:

Unplug the power from behind the printer.

Wait for 60 seconds. 

Hold down the “print photo” and “cancel” at the same time. You should be able to see it with a blank screen for several seconds.

It's done

Try again and again if at first it doesnt work.

Solution 3:

Unplug the all-in-one from power.

Wait 30 seconds.

Plug in the power only.

Repeat steps 2-4 two more times.

On the third time after plugging the unit into power check the functionality. 

Solution 4:

Unplug the power cord from the back of the HP All-in-One.

Wait for the unit to go to the sleep mode. Wait for 60 seconds.

Press and hold Print Photos & Photo Fix buttons simultaneously on the control panel; keep them pressed and reconnect the power cord to the All-in-One.

Continue pressing the buttons until the display goes blank or Reset shows on the control panel display.

Read More

Xerox Workcentre C2424 Errors

31,004.40:6909: it's a mechanical initialization jam error. Pull out the paper tray to make sure it doesn't have a jam. Try also to manually feed some heavy paper or card stock through the printer to make sure the sensor in the preheater isn't stuck.

39,002.40 : DRAM test failure.

39,012.40:56208: "Cycle the power" and if that does not work replace the document feeder.

39,012.41: Document Feeder Optical Failure. Replace the document feeder.

4,0XX.6x: Process Control Software Fault.
Reset NVRAM and then retest.
Ensure ground integrity for the system
Replace the EEPROM chip.
Reboot the system.
From the System Setup menu, go to "Information", "Troubleshooting"
Service Tools menu.
With the cursor at the top of the Service Tools menu, press both the Up Arrow
and Down Arrow buttons to display the Hidden Service menu.
Reset NVRAM is in there.

Read More

Error 04,041.66 on Xerox C2424

4,0XX.6x Process Control Software Fault


Solution 1:


a. Reset NVRAM and then retest.
b. Ensure ground integrity for the system.
c. Replace the EEPROM chip.
d. Reboot the system.


1. From the System Setup menu, go to Information --> Troubleshooting -->
Service Tools menu.
2. With the cursor at the top of the Service Tools menu, press both the Up Arrow and Down Arrow buttons to display the Hidden Service menu.
3. Reset NVRAM is in there




Solution 2:


1. Turn the system power ON.
2. Wait for the Xerox logo to begin moving across the display.
3. Before the logo is centered on the display, press and hold the Back and Info buttons on the control panel.
4. Hold both buttons until the display reads “Beginning Service Mode Initialization”. Release the buttons and the system reboots into service mode with the Service Diagnostics menu displayed.

Read More

Set-up Home Network Printers

Do you know how to fix common issues that may arise while setting up a home network printer?

Network printer helps you to print documents over a local network. These printers can provide plenty of benefits to you. You can share the information to the computers that are connected in the same network. Most homes have more than one system and network printer avoids the installation of printers for every computer. An important role of network printer in your PC is sharing. A network printer in your PC helps to print the data contained in your local network. It can eliminate the extra cost of installing additional printers. Network printer is easy to handle and maintain. At times, you may face issues while installing network printer in your Windows system. However, most of these issues can be fixed even without the help of an expert.

Following are some information about the tips to set-up home network printer:

• Set-up network printer
• Issues
• Tips to fix

Set-up network printer

To set-up network printer in your home network, first of all you need to enable the printer sharing option in your PC. You can enable this option in ‘Control panel‘ of the Windows operating system. To enable this, you need to right click on ‘Printers setting‘ icon. You will have options to choose the sharing in the generated window. To use a network printer in your local network, you need to set an IP address for your printer. You also need to know about the details of your printer before going to set-up the network.

Issues

You may face issues while trying to add network printers, if you have not properly connected to home network and set to the share printers option. You may also face compatibility issues, if your printer is not compatible with the operating system. Sometimes, your PC may not detect the installed printer as well.

Tips to fix

To fix the compatibility issues, you need to ensure the compatibility of the printer before installing. You also need to make sure that your Bluetooth adapter is turned on, if your PC does not detect your printer. You also need to remove viruses from your PC before installing the printer driver. You should ensure the cables and connectors used to connect the printer over network.

Read More

Printing is too slow.

Rev up printer performance--and save ink in the process--by reducing print quality for everyday output. While printer settings vary by model, here's how to switch to draft-printing mode in most Windows apps. Select Print and Properties, and then look for a setting that reduces print quality. With the HP Photosmart 8450, for instance, change the default print quality setting from Normal to Fast Draft (click screen-shot at right). Other speedup suggestions: Print pages from websites without graphics, and add RAM to your printer, if possible. Read "Speed Up Everything" for more tips.

Read More